Cisco Prime Infrastructure—Release 3. They are as follows:. For LED state definitions, please refer to the tables below:. In this guide, both of the methods are documented below. Over-the-air-provisioning is not supported on WLC in Release 8. The Laptop should get an IP address in The Setup Wizard will start.
Create the WLC admin account as shown below. Under the Set Up Your Controller section, please enter the following:. System Name—Enter the System Name. Subnet Mask—Enter the Subnet Mask of the controller. Default Gateway—Enter the Default Gateway for the controller. Under the Create Your Wireless Network, enter the following:. Network Name—Enter the Network Name. This will be the SSID. I am selecting WPA2 Personal. Service Port is typically used out-of-band management and should be on a different network than the controller management network.
Confirm the Settings below. The WLC will go through the reboot. Connect to the console of the WLC High Availability is for box-to-box redundancy. There is no preempt functionality. One can also connect RP port through a L2 switch. Please note the following about the ports:. Only 4x GE ports can be used for direct AP connectivity. If mGig is enabled for 2. To change the speed on the mGig port, follow the procedure below:.
Announcing Cisco Wireless Catalyst - Created by Sudhagar Singh on PM. We are excited to announce the Second refresh of After previous Created by apsood on PM. Wireless Config Analyzer Express v 0.
Created by Javier Contreras on AM. This version now introduces experimental new feature, "Upgrade Advisor, targeted to one of common case generators: what are the supported versions and how to upgrade my current controllers and APs It supports both AireOS and IOS-XE, covering since Updated: July 4, Figure 1.
Table 1. Figure 2. LED Indicators. Figure 4. To deploy WLC , follow the procedure below: Procedure. Please see documentation for more details. If yes, system will save it and reset. Configuration saved! Resetting system with new configuration One can also connect RP port through a L2 switch. To change the speed on the mGig port, follow the procedure below: Procedure.
If the recommended load-balancing method cannot be configured on the Catalyst switch, then configure the LAG connection as a single member link or disable LAG on the controller.
To configure LAG, follows the procedure below: Procedure. To upgrade via USB, follow the procedure below: Procedure. Reboot the controller for update to complete. Optionally, pre-download the image to APs before rebooting to reduce network downtime.
Was this Document Helpful? Yes No Feedback. In the File Name field, enter the name of the configuration file. The default value is Click Upload to upload the configuration file to the server. A message appears indicating the status of the upload. If the upload fails, repeat this procedure and try again. Specify the transfer mode used to upload the configuration file by entering this command:.
Specify the name of the configuration file to be uploaded by entering this command:. If you are using an FTP server, enter these commands to specify the username and password used to log into the FTP server and the port number through which the upload occurs:. When prompted to confirm the current settings, answer y. Information similar to the following appears:.
If the configuration file is encrypted, check the Configuration File Encryption check box and enter the encryption key used to decrypt the file in the Encryption Key field. If you are using a TFTP server, the default values of 10 retries and 6 seconds for the Maximum Retries and Timeout fields should work correctly without any adjustment. However, you can change these values. Optional Enter the maximum number of times that the TFTP server attempts to download the configuration file in the Maximum Retries field and the amount of time in seconds that the TFTP server attempts to download the configuration file in the Timeout field.
Click Download to download the file to the controller. A message appears indicating the status of the download, and the controller reboots automatically. If the download fails, repeat this procedure and try again. Specify the transfer mode used to download the configuration file by entering this command:. Specify the name of the configuration file to be downloaded by entering this command:.
If you are using an FTP server, enter these commands to specify the username and password used to log into the FTP server and the port number through which the download occurs:. When prompted to confirm the current settings and start the download process, answer y. The text file cannot be larger than characters and cannot have more than 16 lines of text. If you are downloading through the service port, the TFTP or FTP server must be on the same subnet as the service port because the service port is not routable, or you must create static routes on the controller.
If you are downloading through the distribution system network port, the TFTP or FTP server can be on the same or a different subnet because the distribution system port is routable. Copy the login banner file to the default directory on your server.
From the File Type drop-down list, choose Login Banner. If you are using a TFTP server, the default values of 10 retries and 6 seconds for the Maximum Retries and Timeout fieldes should work correctly without any adjustment.
Optional Enter the maximum number of times that the TFTP server attempts to download the certificate in the Maximum Retries field and the amount of time in seconds that the TFTP server attempts to download the certificate in the Timeout field. In the File Path field, enter the directory path of the login banner file. If you are using an FTP server, follow these steps:.
Click Download to download the login banner file to the controller. A message appears indicating the status of the download. Log onto the controller CLI. Specify the transfer mode used to download the config file by entering this command:. Download the controller login banner by entering this command:.
Specify the name of the config file to be downloaded by entering this command:. Specify the directory path of the config file by entering this command:. View the download settings by entering the transfer download start command. Enter y when prompted to confirm the current settings and start the download process. Click Clear. When prompted, click OK to clear the banner. To clear the login banner from the controller using the controller CLI, enter the clear login-banner command. Skip to content Skip to search Skip to footer.
Book Contents Book Contents. Find Matches in This Book. Components Used The information in this document is based on these software and hardware versions: An FTP server with the upgrade files stored. A Cisco WLC that runs 8. Follow these steps: Upload your controller configuration files to a server to back up the configuration files. The software releases are labeled as described here to help you determine which release to download. Click a controller software release number: Early Deployment ED —These software releases provide new features and new hardware platform support as well as bug fixes.
Maintenance Deployment MD —These software releases provide bug fixes and ongoing software maintenance. Deferred DF —These software releases have been deferred. We recommend that you migrate to an upgraded release. Click Download. Save the file to your hard drive.
Optional Disable the controller Note: For busy networks, controllers on high utilization, and small controller platforms, we recommend that you disable the From the File Type drop-down list, choose Code. If you choose HTTP you will be prompted for the location of the file. Proceed to step 13 if you choose HTTP. If you are using a TFTP server, the default value of 10 retries for the Maximum Retries field, and 6 seconds for the Timeout field should work correctly without any adjustment.
However, you can change these values, if required. To do so, enter the maximum number of times the TFTP server attempts to download the software in the Maximum Retries field and the amount of time in seconds for which the TFTP server attempts to download the software, in the Timeout field.
In the File Path field, enter the directory path of the software. The default value is Click Download to download the software to the controller. A message indicating the status of the download is displayed. After the download is complete, click Reboot. If you are prompted to save your changes, click Save and Reboot.
Click OK to confirm your decision to reboot the controller. If you have disabled the Optional To verify that the controller software is installed on your controller, on the controller GUI, click Monitor and view the Software Version field under Controller Summary.
0コメント